基于降维算法和等效杆长的可展结构精度分析

考虑铰链间隙和杆件尺寸误差的不确定性并通过概率统计方法对其进行研究,提出了一种基于单变量降维算法(UDRM)和等效杆长模型的可展结构精度分析方法。利用UDRM将可展结构的精度性能函数解耦为多个杆件尺寸误差的独立作用形式,建立精度分析模型。引入等效杆长模型,等效杆件替代原杆件进行精度计算。将铰链间隙与原始杆件尺寸误差合并到等效杆件的尺寸误差中,同时证明了等效杆长尺寸误差近似服从正态分布。以某卫星可展开天线为算例,结合高斯求积公式求解展开状态下精度指标的分布期望和方差。通过与蒙特卡罗模拟(MCS)和一次二阶矩(FOSM)法计算结果的对比验证了本文精度分析方法的正确性和高效性。     

基于扩张状态观测器的动态逆过失速机动飞行控制

针对飞机过失速机动飞行控制问题,提出了一种将动态逆与扩张状态观测器相结合进行扰动估计补偿的新思路。根据时标分离原则将飞机状态分为快变量和慢变量,并分别设计了两个回路的动态逆控制器。在快慢回路分别引入扩张状态观测器对系统的不确定部分进行估计补偿,抵消不确定部分对系统动态特性的影响。最后对控制律进行了过失速机动仿真。结果表明,在存在较大参数摄动情况下,设计的控制律能控制飞机跟踪控制指令,表现出良好的稳定性和鲁棒性。     

缺陷对高温合金蜂窝板弯曲力学性能的影响

采用预埋缺陷的方法,制备含有面芯脱焊缺陷的高温合金蜂窝板,进行了三点弯曲试验,研究了缺陷形状、大小、位置和蜂窝芯取向对蜂窝板三点弯曲损伤模式和承载能力的影响.研究发现,含面芯脱焊缺陷的蜂窝板在缺陷受压部位产生反向鼓包,并沿着宽度方向扩展为完全破坏;随着缺陷尺寸的增大,蜂窝板承载能力逐渐降低;当缺陷位于三点弯曲受拉面时,蜂窝板具有更高的三点弯曲极限载荷,且矩形缺陷试样的弯曲极限载荷要高于相同缺陷面积的圆形试样.最后,利用LS-DYNA对含圆形缺陷高温合金蜂窝板的三点弯曲性能进行了数值模拟分析,得到其三点弯曲过程中的应力分布状态.     

基于新型降阶模型的网格加筋圆柱壳频率分析

针对网格加筋圆柱壳频率分析计算量大的问题,提出一种基于多项式及梁单元形函数的模型降阶方法,即运用多项式及梁单元形函数将复杂结构有限元的节点位移转化为主节点位移,实现模型降阶。并通过控制多项式阶数及梁单元个数来调整降阶模型的分析精度,而降阶模型的计算效率较精细模型有显著提高。以网格加筋圆柱壳为例,对比本文提出的模型降阶方法与3-D实体模型及其他模型降阶方法的频率分析结果,结果表明,提出的模型降阶方法不仅能捕捉到结构的整体模态,还能反映出结构部分局部模态,适用范围广,能够为工程结构设计提供简单有效的计算模型。     

Thermal-structural analysis of regenerativelycooled thrust chamber wall in reusable LOX/Methane rocket engines

To predict the thermal and structural responses of the thrust chamber wall under cyclic work,a 3-D fluid-structural coupling computational methodology is developed.The thermal and mechanical loads are determined by a validated 3-D finite volume fluid-thermal coupling computational method.With the specified loads,the nonlinear thermal-structural finite element analysis is applied to obtaining the 3-D thermal and structural responses.The Chaboche nonlinear kinematic hardening model calibrated by experimental data is adopted to predict the cyclic plastic behavior of the inner wall.The methodology is further applied to the thrust chamber of LOX/Methane rocket engines.The results show that both the maximum temperature at hot run phase and the maximum circumferential residual strain of the inner wall appear at the convergent part of the chamber.Struc tural analysis for multiple work cycles reveals that the failure of the inner wall may be controlled by the low-cycle fatigue when the Chaboche model parameter γ3 =0,and the damage caused by the thermal-mechanical ratcheting of the inner wall cannot be ignored when γ3 ＞ 0.The results of sen sitivity analysis indicate that mechanical loads have a strong influence on the strains in the inner wall.     

交流电子负载校准技术研究

介绍了交流电子负载的校准方法、校准设备和校准原理等。交流电子负载是对是各种交流电源、UPS电源测试和老化试验的主要设备之一,其各项参数指标的优劣对被测设备的检测及故障分析具有重要意义。研究了交流负载的恒定电压、恒定电流、恒定电阻和恒定功率等功能的校准方法和指标,并通过实际测试、校准进行了验证,对校准结果的不确定度进行了评定,校准结果表明本文的校准方法能够满足仪器的技术要求。     

阵风载荷减缓系统故障分析

阵风引起的额外载荷会引起飞机结构疲劳,降低结构使用寿命。采用非定常气动力有理函数拟合方法建立时域状态空间下的动力学系统,设计了阵风载荷减缓系统。研究了阵风载荷减缓系统3种典型故障模式(副翼偏转饱和、舵机卡死、副翼偏转延时)的力学建模方法,并对机翼在阵风减缓系统故障模式下的阵风响应进行分析。仿真结果表明,3种故障模式均不利于阵风载荷减缓系统对阵风载荷的减缓,对于一些特定情况,故障模式下的阵风载荷减缓系统不仅不能减缓阵风载荷,还会带来由副翼偏转不当引起的额外负载。     

The beaming of external Compton emission

We consider a relativistically moving blob consisting of an isotropic electron distribution that Compton-scatters photons from an external isotropic radiation field. We compute the resulting beaming pattern, i.e. the distribution of the scattered photons, in the blob frame as well as in the observer’s frame by using the full Klein–Nishina cross section and the exact incident photon distribution. In the Thomson regime the comparison of our approach with Dermer (1995) results in concurrent characteristics but different absolute number of the scattered photons by a factor of f_corr = 3.09. Additionally, our calculation yields a slightly lower boost factor which varies the more from the corresponding value in Dermer (1995) the higher the spectral index p of the electron distribution gets.     

Laminar flow control research at TsAGI: Past and present

This paper presents a brief review of activities in laminar flow control being performed at the Central Aerohydrodynamic Institute named after Prof. N.E. Zhukovsky (TsAGI). These efforts are focused on the improvement of the existing laminar flow control methods and on the development of new ones. The investigations have demonstrated the effectiveness of aircraft surface laminarization applications with the aim of friction drag reduction. The opportunity of considerable delaying of laminar-turbulent transition due to special wing profile geometry and using boundary layer suction and surface cooling has been verified at sub- and supersonic speeds through various wind tunnel testing at TsAGI and during flying laboratory experiments at the Flight Research Institute (LII). The investigations on using hybrid laminar flow control systems for friction drag reduction were also carried out. New techniques of laminar flow control were proposed, in particular, the method of local heating of the wing leading edge, boundary layer laminarization by means of receptivity control, and electrohydrodynamic methods of boundary layer stability control.     

全数字式操纵负荷系统设计及实现

操纵负荷系统是人在回路仿真系统中的负载模拟装置,它要完成对飞行员十分敏感的驾驶杆力和脚蹬力的仿真,其部件模型的设计满足了操纵负荷系统的通用性。此操纵负荷系统在某型机工程模拟器上的应用测试结果表明,该设计符合直升机飞行模拟器鉴定标准的C级要求。